Flame Temperature and Energy Output as a Function of Flame Color
Flame Shape, Color, and the Composition of Combustion Residues
Regardless of the specific mechanical design of an oil burner, one fundamental principle always applies:
the real work inside the burner is done by the flame.
The flame is the direct result of burner geometry and operating parameters — and flames do not lie.

Flame Shape as a Result of Burner Geometry
Flames may appear long and soft, short and sharp, or anywhere between these extremes.
From a physical perspective, flame shape depends primarily on:
- exit velocity at the nozzles
- nozzle geometry and diameter
- nozzle orientation and spatial arrangement
- spacing between individual nozzles
- supplied air volume and air pressure
Flame shape therefore serves as a direct diagnostic tool, revealing the internal flow behavior and combustion dynamics of the burner.
Measuring High Flame Temperatures – Practical Limits
Direct temperature measurement of flames is technically limited.
Above approximately 2315 °C (≈ 4200 °F), accurate measurement with standard instruments becomes impractical:
- standard thermocouples typically measure up to ~1500 °C (≈ 2730 °F)
- high-temperature sensors (e.g. tungsten–rhenium) are extremely expensive
- infrared pyrometers usually max out at ~2000 °C (≈ 3630 °F)
At higher temperatures, assessment must rely on flame color, combustion residues, and operational experience.
Typical Flame Colors in Waste Oil Burners
In real-world operation, the following flame colors can be observed depending on burner type and tuning:
🔴 Orange-red to orange-yellow flames
Typical for:
- simple evaporation burners
- homemade burners without forced air supply
Temperature: approx. 600–800 °C (≈ 1110–1470 °F)
Observed characteristics:
- heavy tar formation
- oily, sticky soot deposits
- strong sulfur odor (H₂S)
- extremely low efficiency (< 3 kWh/L ≈ < 11 MJ/L)
Stable continuous operation is practically impossible.
🟠 Orange-yellow flames
Temperature: approx. 800–850 °C (≈ 1470–1560 °F)
Observed characteristics:
- severe soot and tar buildup
- unpleasant exhaust odor
- rapid fouling of heat exchangers
- efficiency approx. 5 kWh/L (≈ 18 MJ/L)
Thermally inefficient and operationally problematic.
⚪ Yellow-white, luminous flames
Temperature: approx. 1100–1200 °C (≈ 2010–2190 °F)
Observed characteristics:
- partially coked residues
- incomplete breakdown of dioxins and fluorinated compounds
- efficiency approx. 8 kWh/L (≈ 29 MJ/L)
From an environmental and health perspective, still critical.
🔵 Long blue flames
Temperature: approx. 1900–2000 °C (≈ 3450–3630 °F)
Observed characteristics:
- fully dry, non-oily ash residue
- no perceptible sulfur odor
- improved oxidation of problematic compounds
- efficiency approx. 10 kWh/L (≈ 36 MJ/L)
Significantly cleaner and more efficient combustion.
🔵⚪ Short, sharp blue-white, non-luminous flames
Temperature: approx. 2250–2500 °C (≈ 4080–4530 °F)
In this range, multi-stage, swirling pyrolytic burners exhibit particularly noteworthy effects:
- extremely dry, light-colored ash
- complete decomposition of sulfur compounds
- exceptionally clean heat exchangers
- minimal maintenance (once per heating season)
- efficiency > 11 kWh/L waste oil (≈ > 40 MJ/L)
This combustion regime represents an ecological and energetic optimum.
Combustion Residues and “Chimney Structures”
During extended continuous operation (> 12 hours), chimney-like structures may form within the ash layer.
Through their central channels, pyrolytic gases escape upward.
These structures are:
- mechanically very fragile
- completely dry
- free of visible sulfur residues
They serve as a clear indicator of stable high-temperature pyrolysis.
Influence of Oxidizing and Reducing Agents
Flame color is not determined by oxygen alone.
Other reaction partners — particularly sulfur compounds present in waste oil — also influence flame appearance and can produce orange emission components even at high temperatures.
Comparison with Common Welding Processes (for Reference)
To put the temperature ranges into perspective:
Flame temperatures:
- methane–oxygen: ~2400–2500 °C (≈ 4350–4530 °F)
- propane/butane–oxygen: ~2400–2500 °C (≈ 4350–4530 °F)
- hydrogen–oxygen: ~2500 °C (≈ 4530 °F)
- acetylene–oxygen: ~3200 °C (≈ 5790 °F)
Electric welding:
- arc welding: 6000–15 000 °C (≈ 10 800–27 000 °F)
- plasma welding: up to 25 000 °C (≈ 45 000 °F)
High temperatures are therefore not unusual in engineering — what matters is control, material selection, and process understanding.
Final Remarks
The operating states described above represent the level that many burner designers eventually reach — and where they stop.
Going beyond this point requires a deeper understanding of pyrolysis, fluid dynamics, and high-temperature chemistry.
This is exactly where my development begins.

📍 English navigation block (EN):
✅ Get Access to the Technical Work – License Included
(Protected technical work prepared individually, verified access, license terms, and secure delivery with password.)
⚙️ Zejda Burner Models – Overview & Videos
(All Zejda series burners + technical specs + demo videos)
❓ FAQ – Questions & Answers
(Most common practical questions about burners)
📘 Oil Burners – Foreword
(Introduction for all readers, why this project exists)
🔥 Flame Colors, Temperatures & Combustion
(How flame color relates to combustion quality and emissions)
🧯 Oil Burner Safety – Key Principles
(Safety tips and combustible risks with oil burners, dioxines)
🔬 Emissions & NOx Reduction Techniques
(How to reduce NOx and other pollutants, The Secret)
📏 Measurements & Testing Methods
(How to measure emissions and performance, Phenomena, Dripping Water)
🛠️ Construction, Materials & Maintenance
( Fans, Pyrolytic versus atomizing burner, Materials of high-temperature burners)
💬 Key Technical Principle of High-Temperature Pyrolytic Oil Combustion
( Description of burner technologies)
🛠️ Oil burner and the most suitable hot water boiler
( Boilersfor of high-temperature burners)



