📘
Training chapter for advanced pilot proficiency (STOL / GA / ULL)
1. Introduction
Takeoff from a contaminated surface (e.g., snow, slush, wet grass, waterlogged ground, or snow with an ice crust) belongs among the most underestimated phases of flight. Accident statistics for light aircraft show that insufficient ground acceleration is a frequent causal factor, often resulting in overruns, landing gear damage, or the inability to clear obstacles in the departure path.
One of the advanced pilot techniques—beyond the scope of standard ab-initio training—that significantly improves safety during takeoff from contaminated runways is a maneuver known as the „lift-off burst“, „rip out“, „unstick“ (Czech: „odtrh“). It is a deliberate, pilot-initiated, short-duration lift-off intended to overcome sections of the surface with excessive rolling resistance.
This chapter provides a systematic and technically precise description of the technique, its aerodynamic principles, operational use, limitations, and safety considerations.
2. The gap in current pilot training
No standard pilot training syllabus (EASA, FAA, ULL) describes the pilot deliberately causing the aircraft to lift prematurely from the surface as a formal training maneuver.
Training syllabi typically focus on:
- normal takeoff,
- short-field takeoff,
- soft-field takeoff,
- use of ground effect,
but do not cover a deliberate pilot-controlled increase in lift below Vr or Vlof for the purpose of overcoming contaminated portions of the takeoff roll.
As a result, pilots are often surprised when:
- the aircraft fails to accelerate on a contaminated surface,
- acceleration is extremely low,
- Vr or Vlof cannot be reached within the expected distance—or cannot be reached at all,
- the pilot continues the takeoff roll to the runway end despite low acceleration,
- or the take-off is rejected too late, when a safe stop is no longer feasible.
Video documentation of real incidents in Europe and the USA shows that this affects not only ultralight aircraft but also:
- PPL holders,
- CPL / ATPL pilots,
- general aviation aircraft,
- even powered twin and more-engine aircraft.
3. Definition of the „rip out“, „unstick“, „lift-off burst“
3.1 Basic definition
A „lift-off burst“, „rip out“, „unstick“ is a deliberate, pilot-controlled, short-duration lift-off at a speed below Vlof and often below Vr, performed to:
- traverse a section of the runway with excessive rolling resistance,
- transition the aircraft into very low flight within ground effect (approx. 10–20 cm AGL),
- allow further acceleration in extremely low-level flight beyond the contaminated surface.
3.2 Two forms of the maneuver
There are two primary forms:
1) Terrain-induced hop
The pilot uses a small bump or undulation in the surface.
Bush pilots may intentionally utilize a small root, branch, stone, or tuft to momentarily unweight the landing gear.
2) Aerodynamically induced lift-off
The pilot increases flap deflection shortly before the maneuver and momentarily raises the angle of attack to a value sufficient to lift the aircraft just below stall speed, typically with flap settings between 30–45° or more, depending on the aircraft.
This results in:
- a rapid, short-term increase in lift,
- a simultaneous increase in drag,
- lift-off into ground effect at minimum controllable airspeed.
4. Aerodynamic principles
4.1 Increased lift at high angle of attack
Near stall speed, a wing can generate temporarily increased lift, especially with high flap deflection.
The available lift depends on aircraft weight, density altitude, temperature, engine performance, and propeller slipstream.
This lift:
- is short-lived,
- provides only minimal height (tens of centimeters),
- is sufficient to unstick the landing gear from the ground only!
4.2 Use of ground effect
After the lift-off burst, the aircraft is flown:
- at approx. 0.5 wheel diameter height (typically 10–20 cm) over ground,
- in a region of significantly reduced induced drag,
- with reduced required power to maintain very low-level flight.
This enables acceleration above the ground without the wheels touching the surface and exceeding speeds of:
- Vr (rotation speed),
- Vlof (lift-off speed),
- Vx (best angle-of-climb speed for obstacle clearance).
4.3 Aircraft controllability
At very low speeds:
- aileron authority is limited,
- primary control inputs are rudder and elevator,
- both are strongly enhanced by propeller slipstream.
5. Recommended configurations
5.1 Flaps
Optimal configuration depends on aircraft design.
- Fowler flaps provide the highest lift effectiveness (increased surface area + camber + slot effect).
- Some ultralights allow temporary flap deflections up to 30–40°, in some cases up to 60°, if permitted by the aircraft flight manual.
5.2 Engine and propeller
Before takeoff, verify:
- maximum available engine power,
- correct static and dynamic RPM (e.g., Rotax 912 ULS should reach approx. 5500 RPM during the takeoff roll). When taking off at Vx, it should have 5800 RPM.
- So that the propeller speed corresponds to the increasing speed from Vr to Vx. Ideally, the pilot should have the capacity and skill to change the flap settings and propeller settings from a finer to a coarser angle during take-off, which can take 5-10 seconds. If not, set propeller pitch setting for dense winter air.
6. Procedure for performing the lift-off burst
6.1 Conditions for use
The technique is suitable for:
- deep snow,
- snow with ice crust,
- waterlogged surfaces,
- soft grass with prominent tussocks,
- slush,
- other decelerating surfaces (e.g., dry sand on beaches).
6.2 Step-by-step procedure
- Apply full takeoff power. Setting the propeller angle and achievable engine speed for maximum takeoff power. Verify directional control.
- Extend flaps to the short-field setting (typically ~30°). On some aircraft, rapid manual flap deployment immediately before the maneuver yields the best performance.
- Apply a quick, decisive pitch-up input to increase angle of attack.
- A brief lift-off occurs at minimal height; maintain the aircraft just above the surface, close to stall margin.
- Hold the aircraft in ground effect at approximately 10–30 cm AGL.
- Accelerate through Vr and Vlof.
- Retract flaps gradually (as specified in the AFM) to the setting appropriate for Vx.
- Transition to Vx climb to clear obstacles.
- Turn if you must, preferably in the direction of the propeller’s reaction torque, to improve the aircraft’s aerodynamics. (R 912 to left)
7. What the lift-off burst is not
- It is not an uncommanded bump-induced hop.
- It is not a premature lift-off caused by early rotation.
- It is not an over-rotation.
- It is not a standard soft-field takeoff.
- It is not an uncontrolled flap-assisted liftoff.
The lift-off burst is an intentional, precisely timed pilot maneuver that requires aerodynamic insight and a dedicated training methodology I developed specifically for this maneuver.
8. Practical example – TECNAM P2002 Sierra
A Rotax 912 ULS-powered Tecnam P2002 with a 1720 mm propeller successfully departed a contaminated surface with:
- snow depth 12–20 cm,
- flaps 30–40°,
- properly executed lift-off burst,
- full power, ***
achieving a takeoff ground roll of only 150–170 m.
The video shows:
- lift-off at minimum controllable airspeed,
- brief oscillation after the burst,
- acceleration in ground effect,
- progressive flap retraction,
- smooth transition to Vx.
- ***The takeoff was not executed at full power because the propeller had been set incorrectly, preventing the engine from developing its maximum takeoff performance. This constituted a procedural error. For training purposes, review the video recording with attention to the following parameters:
- Flap deflection at the beginning of the takeoff roll and during rotation.
- Engine RPM, with emphasis on whether the power setting corresponded to the expected takeoff range.
- Pilot management of propeller pitch and throttle throughout the acceleration phase.
- Aircraft behavior during the initial left-turn ground phase take-off, including the influence of reaction torque characteristic of the Rotax 912 series.
9. Risks, limitations, and suitable aircraft types
The technique is not suitable for:
- aircraft with undersized landing gear,
- aircraft with nose gear designs carrying excessive load or small retractable nosewheels,
- heavier GA types with low power-to-weight ratio.
More suitable aircraft include:
- light sport aircraft,
- ultralights with strong engines and large propellers,
- STOL aircraft,
- aircraft equipped with Fowler flaps.
10. Training and competency
The lift-off burst is not included in any national or international basic training syllabus.
It should be taught only:
- after licence issue,
- with a qualified instructor,
- in an appropriate aircraft type,
- in a safe training environment,
- on a suitable surface. Snow provides the best surface. If snow is unavailable, wet tall grass approximately 30–35 cm high can be used in an emergency, though it is less optimal.
Pilots typically develop basic proficiency in this advanced maneuver after 2–3 hours of type-specific training. To ensure safety and efficiency, preparatory exercises must be completed beforehand to reduce workload and stress. Mastery of these foundational steps allows the pilot to execute the lift-off burst confidently, making the maneuver both predictable and controllable under real flight conditions.
11. Conclusion
The lift-off burst is an advanced maneuver that can significantly improve safety during takeoff from contaminated or waterlogged surfaces.
Because it is absent from standard teaching materials and theoretical and practical exams, pilots often lack:
- understanding of aerodynamic principles,
- correct execution techniques,
- awareness of risks,
- knowledge of suitable configurations.
This chapter provides a professional theoretical framework enabling pilots to:
- understand the maneuver,
- recognize situations where it is appropriate,
- understand its limitations and risks,
- and practice it safely with an instructor after initial licensure.
